JMT Mini 260 Racer Quacopter Kit ARF (Assembly No Battery) DIY FPV SP Racing F3 10DOF RC Drone 2.4G 9CH 700TVL HD Camera 5.8G Video Real Time Transmission Quad-Rotor Combo with Lights & Carrying Bag
1x Kingkong 260 PCB 260mm Wheelbase Frame Kit 260mm with LED
2x 2-3S Lipo 2204-2300KV Brushless Motor CW
2x 2-3S Lipo 2204-2300KV Brushless Motor CCW
4x Hobbywing XRotor 15A Brushless ESC Speed Controller
1x Mini Power Hub Power Distribution Board PDB with BEC 5V & 12V
2x 5030 Plastic Foldable Propellers (Pair)
1x Pro SP Racing F3 Flight Controller Deluxe 10DOF with Barometer
1x Tarot 5.8G 32CH 300mW Audio Video A/V Transmitter Tx
1x Galaxy D2 800x480p 7 inch TFT LCD FPV Monitor/ Display Built-in 5.8G 32CH Dual Wireless Receiver
1x 700TVL CCD FPV HD Camera 2.8mm Lens with 1/3″ 960H Exview HAD CCD II
1x Radiolink AT9 2.4GHz 9 Channel Transmitter with Radio R9D Receiver
1x Plastic Landing Skid
1x Tool Set (Bag)
1x Carrying bag for Drone 260
Brand name: kingkong
Item name: 260 Frame Kit
Weight: about 450g(2PCS Frame Kits)
* 36x36mm board, 30.5 mm mounting holes.
* STM32F3 CPU.
* High-capacity Flash (Acro 6DOF and Deluxe 10DOF)
* MPU6050 Accelerometers and Gyroscopes
* MS5611 Barometer (Deluxe 10DOF)
* HMC5883 (Deluxe 10DOF)
* MicroUSB socket.
* 4 x 4 pin JST-SH Socket (I2C, SWD, 2xuart)
* 2 x 8 pin JST-SH Socket (PPM, PWM, SERIAL RX, GPIO, ADC, 3V, 5V, GND)
* 8 x 3 pin though-holes for pin headers for ESC / Servo connections.
* 2 x 4 pin though-holes for the 2x serial ports .
* 2 x 2 pin though-holes for battery voltage and buzzer.
1 Fast response, 3ms only, which is much less than the average 20ms even 9 channels it acts synchronously.
2 Support English & Chinese Menu. Including helicopter 8 swash plate models, fixed wing 2 airfoils 3 rears, gliders 4 airfoils and 2 rears. Freely operating any styled aircraft
3. Programmable mix control. Basic menu, Advanced menu,Graph view for varieties of throttle and servo curve.
4 DSSS spread spectrum mode supplies better performance in anti-interference
5 Adopt two-transmission technology of RadioLink AT10 10CH Radio Control, support signal strength, receiver voltage monitored, and extending battery voltage, temperature, motor RPM, GPS etc.
6 4096 section precision, 0.25us per section, servo anti-shake rudder
7 2.8 inch 16 colors LCD resolution 240×320 distinct and magnificent
8 Actual measurement: ground 600 meters, air 1000 meters
9 Vibration alarm
10 Support USB online upgrade
11 Four VR switches, three three-way switches, four two-way switches, a reset trainer switch.Support multiple aerial control mode and PTZ control.
FPV TX & RX:
Integrated automatically scanning channel function, a key to search signal, easy to operate;
Built-in 32CH Dual receiver, dual diversity reception, two receiver modules receives signal independently by different channels.
Built-in 3CH 5.8G AV output (R1, R2 and Diversity) and 1CH AV input.
Built-in 3.7V 4000mAh battery makes you work for more than 3 hours, when it is fully charged.
With two holders (control holder and Triangle holder), the control holder can work with radio with mental handle (plastic handle isn’t supported temporarily)
Special BOSCAM holder structure, it is quick and easy to be installed on the radio (about 10s), especially for DJI Phantom radio. You can adjust the position of monitor on the radio with the universal ball and adjustment shaft.
The equipped charger wire can connect with 3S battery as external power supply, so that you will not worry about the end of built-in power consumption in outside.
A foldable sun hood is included to optimize viewing in bright conditions.
– Weight: 11G (without antenna)
– Dimension: 23.5×363×12.5MM
– Working Frequency: 5645-5945MHz
– Channel: 4 bands / 32 channel
– 5-DIP switch
– Output Power: 27.5 dbm (300mw)
– Input Voltage: DC 7-26V (2-6S)
– Output Voltage: 5V 1A
– Antenna Adaptor: RP-SMA 50Ω
– Working Temperature: -10 ~ 60 degrees.
– Frequency: FM
1.Install the antenna before connecting the power to avoid further damage.
2.Choose proper working frequency and tune the receiver to the same frequency. Please refer to the channel list.
3.Do not touch the surface of transmitter while operating. It is normal the surface is getting hot.
4.The input voltage range is between 7-26V (2-6S), do not overload the working voltage.
5.The output voltage is 5V1A. Please confirm the current and voltage of the camera
Caution for the battery:
Don’t over-charge, or over-discharge batteries.
Don’t put it beside the high temperature condition.
Don’t throw it into fire.
Don’t throw it into water.