DIY RC Drone Quadrocopter Full Set RTF With X4M380L Frame Kit with APM 2.8 flight control Motor ESC Props AT10 Transmitter 11.1V 3300Mah 25C Battery Unassembled,buyer need to assemble by themselves.
X4M380L Fiberglass Frame *1
Clockwise Brushless Motor *2
Counter-clockwise Brushless Motor *2
30A Brushless ESC Speed Controller *4 9443 Propeller *2 KK Connection Board *1 APM2.8 Flight Control *1 6M GPS with Compass *1 3.5mm Bullet Connector *12 20cm Hook and & Loop Fastening Tape *1 T Plug Male Connector Silicone Wire *1 5pcs 10cm Servo Receiver Extension Lead Wire Cable*1 GPS Folding Antenna Mount Holder*1 11.1V 3300Mah 25C Lipo Battery *1 Radiolink AT10 Transmitter *1 IMAX RC B3 Pro Compact Balance Charger *1
Before you can configure your APM,
you will need to first connect everything together.
This guide will show you all the cables and parts that you will need to connect to your APM.
Typical Quadcopter Layout
Please note the illustration Below highlights a (TYPICAL) installation. It contains optional equipment including a Camera Gimbal and a Battery Monitor and it utilizes an ESC wired “Y” power connection rather than the power distribution board common to many MultiCopters.
1. Connecting your motors and RC gear
| If you are using female to female servo cables, the ground (black) side of each connector must be on the outside for the board, the signal (white/orange) needs to be on the inside as shown below.|
Please note, that your ESC, connectors should be plugged in the the output side, it is suggested that you only use power from one of your ESC’s. This can be dune by cutting the red wire on all but one of the ESC’s, or by using a special adaptor.
2. Connecting ArduCopter motors
Sonar – Ultrasonic Rangefinder
AC2 supports the MaxSonar line of sonars for low level altitude hold and in the future collision avoidance. Below 10 meters sonar is primarily used for altitude hold. Above 10 meters, the barometric sensor is used. GPS is not required for altitude hold.
Connect your Ultrasonic Sensor to the A0 port of your Ardupilot Mega v2 board
| The sonar sensors are quite sensitive to noise, adding something like a ferrite choke to your cable could help. The most important is to mount your sonar away from other electronics like ESC, or wireless telemetry modules.|
Possible Causes of sonar Interferance
Two colors for choose,please tell us which one you prefer in advance,or we will ship it according to our inventory,thanks.
Multiple function remote control system,including helicopter,airplane and slider three type flying machine and five models,cover almost every popular model,you can fly any model by this radio.
3.5 inch colorful screen 320×480 resolution,clear display menu and graphs.
Great control distance: 1.1km on the ground,2km in the sky.
Expansion feedback module,users can get plane details in real time.
Make very setting clear and exactly output result.
Fast response time only 3ms to the operation,faster then the other transmitter 20ms,even ten channels also let you feel it.
High channel resolution reaches 4096,0.25us per resolution let all the servos keep tranquil.
Strong anti-jumping,DSSS(Direct sequence spread spectrum) technology.
Unbelievable price, high quality as supper bland, and more exactly, faster response, higher resolution,one and the only one anti-jumping DSSS technology.really worthy to have it.
3. Frequency:2.4GHz ISM band(2400MHz~2485MHz);
4. Modulation mode:QSPK;
5. Channel bandwidth:5.0MHz;
6. Spread spectrum:DSSS;
7. Adjacent channel rejection:>38dBM;
8. Transmitter power: <100mW(PCB testing),
<20dBm(3 meter air testing);
9. Operating Voltage:8.6~15V;
10. Operating Current:<95mA;
11. Control distance:800 meters ground;
12. Channel:10 Channel,8~10 channel are customizable;
13. Compatible model: Include all 120 degree and 90 degree swashplate helicopter,all fix wing and glider,five flying model;
14. Simulator model:under the simulator model the transmitter action turn off,change to power saving model;
15. Screen:16 colorful screen,size 78×52mm,320*480 pixel.