We accept OEM orders,if you have special request for the item or other items you need to produce,please feel free to contact us,we will try our best to give you best quotation and serves~~~
DIY Q250 FPV Racer Drone PNP S-Tower Flight Control Glass Fiber Frame with 700TVL Cam FASST Mode TX 2300KV Motor F09206-H
Please Note : We will help buyers to solder ESC with power board , if you needn’t , please kindly remark to us , thank you so much .
Package Listing :
Glass Fiber Mini Alien Across 250mm frame kit *1
JMT RS2205 2300KV CCW Motor *2
JMT RS2205 2300KV CW Motor *2
XT-XINTE 22 Motor Mount (Black ) *1
5045 5×4.5×3/5040 5x4x3 3-Blade CW CCW Clear Single Color Propellers *1
FLYCOLOR Raptor S-Tower ESC5V/12V 30A 4-in-1 ESC *1
700TVL CCD FPV HD Camera 2.8mm Lens with 1/3″ 960H Exview HAD CCD II *1
RGB 5050 LED Light Board 5V 12V 3S 4S 7 Colors Switch *4
5X Hook and & Loop Fastening Tape *0.02
for DJI Phantom FPV image transimitter 5.8G Mushroom Antenna *1
FPV 5.8GHz 600mW 32 Channels Mini Wireless A/V Transmitting (TX) Module TS5828 RP-SMA *1
Tarot FASST Mode Receiver TL150F2 Compatible 2.4GHz FUTABA FASST Air System SBUS RX *1
Frame kit specifications :
The Mini Quad is a low weight Mini Sport FPV Quadcopter frame.
This allows the quadcopter to compete with larger quadcopters, while being smaller and agile ! Working on Mini Quadcopters requires a lot of soldering, wire shortening and creation of power distribution systems. This product requires a good knowledge of RC systems and is not recommended for beginners. Materials: Glass Fiber Fasteners: Stainless Steel & Red Metal 8/8 Size: 220mm diagonally, 175mm wide, 130mm long motor-to-motor; about 1/2 the size of a regular quadcopter Maximum Propeller: 5″ Motor Mount: M2 12mm – 16mm (Tiger MN1806 2300kv, RCX 1804 2400kv), M3 19mm (Tiger MT2206 2000kv, Sunnysky X2204 2300kv) Flight Controller Mount: 30.5mm x 30.5mm Board Camera Mount: 32mm x 32mm
S-Tower Flight Control specifications :
Modern techniques,Light S-Tower,Double signal transmission,Outside pad,Fast cable
Size:41.5 x 36 x 19.6 mm
Tarot FASST Mode Receiver specifications :
1.1 Compatibility:FASST 2.4GHz Air Systems(7CH Mode/Multi Mode):6EX,7C,TM-7,TM-8 T8FG,T10C,TM-10,T10CG,T12Z,T12FG,TM-14,T14MZ etc.
Working temperature range:-10~+80°
Operating voltage range:3.5~8.4V
Output signal:RSSL & S.BUS(1CH~16CH)
Servo frame rate:14ms(FS-normal speed mode)
7ms(HS-high speed mode)
1)Compatible with FASST 2.4GHz Air Systems(7CH Mode/Multi Mode);
2)With RSSL output;
3)Adopt american-made IC,improve sensitivity and stability;
4)Compatible with Futaba S.BUS servos;
5)Ideal for the FPV racing drones competition.
2.1 Bind procedure:
Turn on the transmitter,connect the battery to the receiver while pressing receiver is F/S button.After the red LED is off and green LED is solid the binding process is completed and the receiver is operating normally.
2.2 LED status:
3.HOW TO SWITCH BETWEEN HS Mode with FS Mode
Turn the transmitter off,connect the battery to the receiver,press the F/S button of receiver for 6 seconds and then release.the red LED will flash fast in HS Mode and slow in FS Mode.Repeat this to alternate modes.
WARNING:HS mode is only applied for high-speed digital servos.Other servos should select FS mode otherwise servos will get hot or even burn out.