Panel Figure Each key machine functions as follows:
1. PLAY / PAUSE– press PLAY / PAUSE, the machine from the “pause” switch to “Play” or by a “Play” to switch to “time out”. [SHIFT] + PLAY / PAUSE: SAMPLE 4 PLAY- Press SAMPLE 4 PLAY button to start / stop playback sample 4. [SHIFT] + PLAY / PAUSE: SAMPLE 4 REC- Press SAMPLE 4 REC, music players to sample 4. 2. CUE key – Press CUE button will return to the Cue point position setting and pause music playback. (If you are not useful to set the PAUSE button CUE point, CUE point mark position defaults to the starting point of the song.) In this case, hold down the CUE button will start playing, when loose CU keys, the music playback position will return to set up good CUE point and pause. Press the key and press the PLA CU key, then release both keys at the same time, the music will play continuously normal [SHIFT] + PLAY / PAUSE: SAMPLE 3 PLAY Press SAMPLE3 PLAY button to start / stop playback sample 3. [SHIFT] + PLAY / PAUSE: SAMPLE 3 REC Press SAMPLE 3 REC, music players to sample 3. 3. PITCH – – Press PITCH BEND -, pitch value will decrease, play deceleration, after the release and return to its original state. [SHIFT 1] + PITCH: SAMPLE 2PLAY- SAMPLE 2 PLA hold down the button to start / stop SAMPLE 2 broadcast Release. [SHIFT 2 + PITCH: SAMPLE 2 REC- and hold the SAMPLE 2 REC button, the playback position is SAMPLE2. 4. PITCH + – Press PITCH BEND +, pitch value will increase, playback acceleration, after release, return to the original state. [SHIFT 1] + PITCH: SAMPLE 1 PLAY- and hold the SAMPLE 1 PLAY button to start / stop SAMPLE 1 Play. [SHIFT 2] + PITCH: SAMPLE 1 REC- and hold the SAMPLE 1 REC button to record the playback position SAMPLE1. 5. AUTOLOOP- AUTOLOOP switching functions on and off. [SHIFT 1] + AUTOLOOP: HOT CUE2 second set CUE point. [SHIFT 2] + AUTOLOOP: REC 2 resets the second CUE point. 6. LOOP + select auto loop beats, when the loop playback, each time you press the button, the length of the loop playback on increase Doubled. [SHIFT 1] + LOOP +: HOT CUE1 setting the first CUE point. [SHIFT 2] + LOOP +: REC 1 reset first solo CUE point. 7. LOOP- select auto loop beats, when the loop playback, each time you press the button, the length of the loop playback is reduced Half. VDC-100M 11 [SHIFT 1] + LOOP +: HOT CUE3 third set CUE point. [SHIFT 2] + LOOP +: REC 3 Reset third CUE point. 8. SYNC– Press the SYNC button to set the corresponding channel music, tempo-driven tempo, while blocking the other channels are set Home. 9. FX ON switch the sound of the opening and closing press the E button. 10. Filter– clockwise rotation to high filter, rotate counter-clockwise to lower the filter. [SHIFT 1] + Rotate: Search: playing track in the search. [SHIFT 2] + Rotate: parameter 2– and sound adjustment select the relevant parameter values. 11. High– adjust the music treble response. [SHIFT 1] + Rotate: Gain: clockwise rotation can increase the signal strength of each channel. [SHIFT 2] + Rotate: parameter 1– and sound adjustment select the relevant parameter values. 12. Low– adjust music audio sound. [SHIFT 1] + Rotate: Mid: adjust music audio sound. [SHIFT 2] + Rotate: KEY– adjust parameter values associated with KEY sound. 13. Volume– adjust the music volume. [SHIFT 1] + Rotate: SAMPLE VOLUME: SAMPLE VOLUME rotary knob to adjust the sound, along Clockwise when the volume increased, the volume decreases counterclockwise rotation. [SHIFT 2] + Rotate: FX SELECT– rotation FX SELECT button to select the currently playing music can sound. 14. HEADPHONE CUE– press HEADPHONE CUE button, the headset will sound out. 15. SEARCH– Press SEARCH button, the machine into the Scratch mode, Jog Wheel friction sound. 16. SHIFT 1: Press SHIFT1 key and other keys, key color blue. 17. SHIFT 2: Press SHIFT2 key and other keys, key color red. 18. BRIWSE KNOB- turn this button selects the music track, pressing this button to enter or exit the folder. 19. FOLDER OUT: After searching finished folder FOLDER OUT can return to the previous file. 20. LOAD A- Press this button in the left channel to the folder you want to play music. [SHIFT 1] + PRESS: PAGE RIGHT: The right of the playback file is switched to the left, RECORD-EFFECTS-SAMPLER-BROWSER. [SHIFT 2] + PRESS: WAVE ZOOM– widen the playing track waveform. 21. LOAD B- Press this button to the folder in the right channel you want to play music. [SHIFT 1] + PRESS: PAGE RIGHT: The left side of the playing file to switch to the right, RECORD-EFFECTS-SAMPLER-BROWSER. [SHIFT 2] + PRESS: WAVE ZOOM– compression wave track being played. 22. MASTER VOLUME: adjust the main output signal strength. [SHIFT 1] + PRESS: CUE VOLUME- adjust the headset audio output. [SHIFT 2] + PRESS: CUE MIX– adjust the headset volume and master volume balance output volume. 23. CROSSFADER: Switching left and right channel audio output. 24. JOG WHEEL: Scratches function can be enabled when VINYL open, PITCH BEND function VINYL Close Enabled. [SHIFT 2] + Rotate: parameter 1– and sound adjustment select the relevant parameter values. [SHIFT 2] + Rotate: parameter 2– and sound adjustment select the relevant parameter values. 12 Front and back illustration 1. POWER INPUT: By connecting the USB cable to the machine power. 2. LINE OUT: unbalanced stereo audio signal output of the main volume, external amplifier or other device, the output to From a computer or other external sources. 3. MIC JACKS: XLR connections through which MIC 6.3mm socket. 4. MIC VOLUME: adjust the MIC volume. 5. HEADPHONE VOLUME: adjust the headset volume. 6. HEADPHONE JACK: Headphones can be connected automatically after listening to music.