USD 1.94/piece USD 1.39-1.59/piece USD 2.55-2.71/piece USD 1.35/piece USD 1.65/piece USD 1.39-1.45/piece USD 2.28/piece USD 1.14/piece
The new FPV head tracker video glasses, high-definition display module (854 * 480), built-in head tracking gyro circuit, remote control support futaba head tracking.
5.8G 32 full-frequency receiver frequency, dual hardware receive double the receiving antenna.
Built-in front-view camera, do not pick the glasses case, see the front of the image.
2-6S voltage input section,
Especially for the players as well as aerial PTZ FPV-handed use.
Note that JR does not support remote control (the remote control is not supported) head tracking.
The FPV glasses built two 5.8GHz receiver module and two antenna ports, work on diversity reception mode to achieve good signal utilization, improve image quality.
You can set four bands and eight channels on each band (the band corresponding to the range of channels, check the product specifications section)
Long press BAND button to enter the menu band, when the band entered the menu will beep indicating the current band.
In this mode, three seconds if you do not operate the band button will automatically exit the band set up (emit a short beep) to enter the normal operating mode.
Press CH button to cycle between CH1, CH2 … CH8, CH1 …, and beep indicating the current channel after the operation.
PPM channel settings
Press and hold the power button and HT will enter Head Tracker menu (immediate release after turning on the power button), head tracking will beep indicating the current working channel PPM, below.
Press the button to select HT PPM channel, press the button to enter Pan HT tracking range setting mode.
Pan tracking range set
Pan entered tracking range setting mode will beep indicating the current scope of work, a long beep to 90 degree, 2 long beeps to 180 degree.
Press HT button to change the scope of work, and the issue of corresponding beep.
After setting Press HT button to exit the current mode (it will emit a short beep), and return to the PPM channel setting mode.
After setting the parameters of a head tracking, please disconnect the power and re-power will enter the normal head tracking.
During use, press HT button to head tracking to the center position.
The FPV glasses preceded by a wide-angle camera, and has a 640X480 (VGA) resolution and excellent low light characteristics, making use of this feature can be very easy to observe the surroundings rather than off FPV glasses.
Press the CAMERA button to open the front camera. Volume
Each boot volume is automatically set to the lowest volume (suddenly issued a strong volume while avoiding the boot)
When the volume is adjusted to the maximum or minimum, if it continues to operate, it will issue a long beep prompts.
Interpupillary distance (IPD) Adjustable
Toggle IPD regulator may change Interpupillary distance.
Brightness / contrast settings
By 5 can be very convenient to control display brightness key / contrast, short press can be gradually adjusted, long press can continuously adjust the image changes, do not operate the button for 5 seconds will automatically save these settings.
Press the middle button to Brightness / Contrast restored to factory settings
FOV: 30 Degrees
Resolution: 854 * 480(WAGV) 1,229,760 color sub pixels
IPD: 60-68mm adjustable
Antenna port: 2 x 5MA, 50ohm
Video standard: NTSC/PAL
Video Output: 75ohm
Audio Output: 10kohm
FOV: 120 Degrees(diagonal)
Resolution: 640 * 480(WAGV)
Focal length: f=0.95mm
Sensor: magnetic, inertial and gyro
Output: PPM 8 channel, optional 5-6ch, 5-7ch, 5-8ch, 6-7ch, 6-8ch, 7-8ch
DC IN: DC 7-28V/1A
Power consumption: 12V input: 4.3W
Size: 168 x 92.5 x 41mm
Package size: 195 x 135 x 60mm
Net weight: 345g
Package weight: 575g
1 x FPV goggle
1 x Carry Case
1 x futaba data cable
1 x JR data cable
1 x WFLY data cable
1 x AV cable
1 x Power cable
2 x 5.8G 2db antenna
(Retail Package is Not included)